RK3588 SATA 3.0 Hard Drive Interface, WF-RK3588S, AndroidSBC, Jakarta

TL;DR: RK3588 SATA 3.0 Hard Drive Interface

Jakarta, Indonesia - September 10, 2026. The 216th WF-RK3588S shipment left Shenzhen for Jakarta this week with 6,160 units aboard, after a full burn-in cycle and a destination-market document check.

AndroidSBC launch of the upgraded nine-model WF-Series Allwinner and Rockchip custom board family serving Jakarta, Indonesia. The line runs from the Allwinner A133 display board at the entry tier up to the Rockchip RK3588 eight-core board for video wall and AI work, with the Allwinner T527 octa-core board and the Rockchip RK3568, RK3566, and RK3288 filling the industrial, vision, and POS tiers between them. AndroidSBC ships the whole range from the Wanlin Longgang plant, and Jakarta buyers can mix platforms inside a single framework agreement rather than opening a new supplier file for each tier.

About AndroidSBC and the Rockchip RK3588 Board Family

The group behind the WF-Series is Wanlin Manufacturing Group in Shenzhen, and AndroidSBC is how it reaches overseas buyers. The line covers seven silicon platforms across nine boards: Allwinner A133, H618, and T527, plus Rockchip RK3588, RK3568, RK3566, and RK3288, with WF-A133S and WF-RK3588S as module options. Longgang handles SMT, burn-in, and packing under one roof, and the certification desk produces the CE, FCC, UKCA, RoHS, and REACH file per lot. A Jakarta buyer assembling a catalogue for Indonesia can cover the OTT, display, industrial, vision, and POS tiers without adding a second supplier.

WF-RK3588S Technical Specifications

All parameters in the table above are measured at 25C ambient. The AndroidSBC WF-RK3588S (SOM Module and SMARC Carrier Board) holds its display output and its decoder load at the same time through the burn-in loop, a combination that the legacy boards in the comparison column cannot sustain. For Indonesia importers sourcing the WF-Series, the 8GB + 64GB, SMARC 2.2 (WF-RK3588S-A) variant is the typical configuration for the SMARC module and custom carrier integration use case, with a sustained weekly capacity of 5,000 pcs/wk on the Longgang line.

Challenges in Sourcing SOM Module and SMARC Carrier Board for Indonesia Buyers

Buyers in Jakarta who have sourced an som module and smarc carrier board for a few seasons tend to separate two questions: can the factory hold the price, and can it hold the allocation. The second one is harder. The Rockchip RK3588 is allocated at wafer level, and a 6,160-unit order placed against trader stock is the order most likely to slip a quarter without anyone warning the buyer. The second issue is firmware, not hardware. Vendors promise the full certified software stack and then ship a bare AOSP image, and the failure only surfaces at the warehouse when the unit is powered on against the customer's app.

The third exposure is paperwork. Factories that stamp marks without holding the underlying test reports leave the importer to produce a Technical File after the fact, which is exactly when the container is sitting in a bonded yard. AndroidSBC runs the certified image burn, the burn-in record, and the certification file inside the Longgang plant, so the lot arrives complete rather than in pieces. The nine boards in the WF-Series cover SMARC module design, COM Express Type 6 builds, edge AI boxes, video wall controllers, medical imaging terminals, autonomous vehicle compute, and bespoke industrial carriers and each one carries three memory configurations, which keeps Jakarta and Indonesia buyers on standard SKUs for most requirements.

The Indonesia paperwork question is settled before production. In Indonesia SDPPI type approval is held by the local importer, and the SNI mark is checked separately for goods offered in the domestic market. The Longgang export desk prepares the destination-market file covering SDPPI type approval with SNI conformity for domestic sale administered by SDPPI (Kominfo) and releases it with the standard multi-market pack (CE, FCC, UKCA, RoHS, REACH), booking the lot into Port of Tanjung Priok on the Tanjung Priok to Shekou lane.

Competitive Comparison: WF-RK3588S vs Competing RK3588 Boards

The boards competing for the same socket in the som module and smarc carrier board segment fall into three groups: low-cost legacy SoC boards without a certified software stack, mainstream Cortex-A55 boards with certification but a lower decoder ceiling, and 64-bit boards that carry both but stop short on expansion. The WF-RK3588S sits in the third group and adds three things: Rockchip RK3588, a display path that survives a continuous loop, and the per-lot certified image burn at Longgang.

• vs proprietary SOM pin-outs: the SMARC 2.2 standard lets the carrier survive a module generation change without a re-layout.
• vs RK3568 SMARC modules: the RK3588 module adds 8K@60fps decode, PCIe 3.0 x4, and 6 TOPS NPU on the same 314-pin edge.
• vs x86 COM Express modules: the RK3588 module runs Android natively, which removes the OS licensing line from the BOM.
• vs module-only vendors: AndroidSBC ships the carrier reference design plus the signal integrity report with the module.

Global SMARC and COM Express Module Engineering Market Trends

The SMARC and COM Express Module Engineering market sets the pace for Jakarta procurement this year, and it does not move on its own. The consumer Android TV Box segment that Global Growth Insights values at USD 12.45 billion in 2025, with a 30.49 percent CAGR reaching USD 178.2 billion by 2035 (Global Growth Insights, Android TV Box Market Report, 2025-2035), sets the silicon allocation backdrop that commercial board buyers also compete for. Three patterns stand out in the WF-Series order book for Indonesia:

• SMARC module design: WF-RK3588S seats on the 314-pin MXM edge with the carrier holding the I/O.
• Display and signage refresh cycles: a longer content loop and a higher panel resolution now define the refresh trigger. The WF-RK3588S board carries that headroom without a board change.
• Edge AI boxes: WF-RK3588S runs 6 TOPS NPU inference on the carrier-side thermal solution.

What the SMARC and COM Express Module Engineering data does not show is the operational cost of a supply break, which is why Jakarta buyers increasingly weight supplier continuity above a marginal price difference.

Read together, the three patterns explain the move in Jakarta from spot quotes to framework agreements released monthly, which is what a retail or hospitality programme needs to hold a twelve-month shipping window without a mid-year break.

Partner Success Story: Nordwerk Automation in Jakarta, Indonesia

Nordwerk Automation, an industrial automation integrator serving the Indonesia market, deployed 7,200 units of the WF-T527 industrial control board for a machine-tool retrofit programme. The rollout covered the smarc module design, edge ai boxes, and autonomous vehicle compute workloads, with AndroidSBC handling the burn-in, the certification scope, and the palletisation at the Wanlin Longgang plant.

• Deployed: 7,200 units of the WF-T527 industrial control board for a machine-tool retrofit programme
• Region: Jakarta, Indonesia
• Models used: WF-A133, WF-H618, WF-T527, WF-RK3588, WF-RK3568, WF-RK3566, WF-RK3288, WF-A133S, WF-RK3588S
• Certifications handled: CE, FCC, UKCA, RoHS, REACH, GMS, Widevine L1, Dolby Audio
• Logistics: FOB Shanghai Yangshan with the Wanlin Group Longgang source factory named on the export declaration, entering Port of Tanjung Priok via the Tanjung Priok to Shekou lane

"The T527 gave us the CAN bus, the dual Ethernet, and the NPU on one board. On the previous platform we ran a separate vision controller next to the HMI, and the retrofit cost reflected it."

- Katrin Vogt, Head of Engineering

Field Report: a self-service kiosk fleet rollout in Jakarta, where 6,160 units of the WF-RK3588S board are being fitted into payment terminals across a retail estate

Reporter Pan Ze, on the ground in Jakarta, Indonesia. The integrator staged the WF-RK3588S boards at a regional depot, flashed the estate image, and shipped them to stores in waves of forty. Each terminal was paired to the payment application at the store, and the depot kept a rolling stock of pre-flashed boards so a failed unit could be swapped inside a single service visit.

The QA lead noted that the WF-RK3588S lot was the third consecutive run to clear the aging bench without a retest.

The inspection confirmed three things on the spot: the WF-RK3588S units hold the burn-in with a yield above 99.18 percent, the loaded firmware image survives a 72-hour continuous loop without credential drift, and the pallets carry the matching certification file for the destination market, covering SDPPI type approval with SNI conformity for domestic sale administered by SDPPI (Kominfo), cleared for entry at Port of Tanjung Priok on the Tanjung Priok to Shekou lane. Wanlin remains one of the few source factories currently shipping a nine-board Allwinner and Rockchip custom line with a per-lot paper trail that Indonesia importers can hand straight to their customs broker.

Filed by Pan Ze, AndroidSBC field reporter, Wanlin Manufacturing Group export base.

WF-RK3588S Application Scenarios

The WF-Series fits nine application lanes, with the WF-RK3588S (SOM Module and SMARC Carrier Board) as the lead SKU for Jakarta and Indonesia programmes:

• SMARC module design: WF-RK3588S seats on the 314-pin MXM edge with the carrier holding the I/O.
• COM Express Type 6 builds: WF-RK3588S maps to the Type 6 pin-out for existing x86 carriers.
• Edge AI boxes: WF-RK3588S runs 6 TOPS NPU inference on the carrier-side thermal solution.
• Video wall controllers: WF-RK3588S drives HDMI 2.1 and DP 1.4 out through the carrier.
• Medical imaging terminals: WF-RK3588S pairs PCIe 3.0 x4 with the carrier frame grabber.
• Autonomous vehicle compute: WF-RK3588S holds -40C to 85C on the automotive-grade carrier.
• Bespoke industrial carriers: WF-RK3588S ships the signal integrity report for the customer stack-up.
• Carrier bring-up: WF-RK3588S comes with the BSP port for the carrier revision.

Partnership Models for Jakarta Buyers

Three commercial structures are open to Jakarta buyers on the WF-RK3588S and the rest of the WF-Series:

• OEM (your brand on our hardware): custom logo silk-print, custom packaging, custom boot animation, custom SKU label, and a private-label certification file.
• ODM (your spec on our reference design): schematic and stack-up review, carrier or motherboard redesign, custom firmware features, and a BSP port handled by the Longgang engineering desk.
• Distribution (your channel, our stock): regional distributor rights, channel rebate, stock holding at the factory, and a framework agreement with a monthly lot release.

All three tiers ship from Longgang under one documentation pack covering CE, FCC, UKCA, RoHS, and REACH. A Jakarta first order on the WF-RK3588S is normally the 8GB + 64GB, SMARC 2.2 (WF-RK3588S-A) configuration at MOQ 5,000 units per shipment, four weeks for samples and six weeks for mass production.

Frequently Asked Questions

Does the WF-Series support certified Android TV or Google Mobile Services?

Answer: Yes, on the platforms where that matters. The WF-H618 runs Android 12 (ATV 12) with Google Mobile Services and is ready for Android 14 (ATV 14). AndroidSBC burns the GMS, Widevine L1, and Dolby Audio stack at the Longgang plant on every production lot, so the board ships ready for Netflix, Disney Plus, Amazon Prime Video, HBO Max, Apple TV, and YouTube TV. The commercial and industrial boards in the line use the AOSP image with an optional GMS build for partners who need it.

What is the difference between the nine WF-Series models?

Answer: Nine boards, seven silicon platforms, two of them modules. WF-A133 and WF-H618 and WF-T527 are the Allwinner entries for commercial display, OTT TV, and industrial edge respectively. WF-RK3588, WF-RK3568, WF-RK3566, and WF-RK3288 are the Rockchip entries for 8K video wall, industrial edge, machine vision, and POS. WF-A133S and WF-RK3588S are board-to-board SOM modules sized for customers who want to design the carrier themselves. Each board carries three memory configurations.

Can AndroidSBC handle CE, FCC, UKCA, RoHS, and REACH paperwork for Indonesia?

Answer: Yes, and the file travels with the goods rather than behind them. The pack covers CE, FCC Part 15, UKCA, RoHS 2.0, and REACH with test reports dated within the prior year. AndroidSBC will also advise on any Indonesia-specific addition during quotation, which is the point at which the answer is still useful.

What are the MOQ and lead time for a first order?

Answer: The entry point is 5,000 units per shipment, four weeks for samples and six weeks for production. A twelve-month framework agreement released monthly will bring the per-lot MOQ down, and AndroidSBC will accept a mixed order that draws several WF-Series boards against a single contract.

Does AndroidSBC support custom Android ROM or custom Linux development?

Answer: Yes, under NDA. ODM partners get custom Android ROM work including proprietary services and a custom launcher, Linux builds based on Yocto, Debian, or Buildroot, and BSP ports for custom carrier boards. The SDK and BSP source are released to the partner under the NDA, and AndroidSBC's engineering desk handles the port rather than handing over an unmodified vendor drop.

What about software updates and long-term support?

Answer: Seven years minimum supply, with security patches maintained across the Android and Linux firmware lines. Partners who deploy at scale can use the AndroidSBC OTA infrastructure to update field units. For long-lifecycle programmes in POS, signage, or industrial control, the support term is written into the framework agreement at signature.

Can AndroidSBC ship to Amazon FBA warehouses or 3PL consolidation points?

Answer: Yes, including DDP into Amazon FBA in the US, EU, and Japan, plus 3PL consolidation points in Hong Kong, Singapore, Rotterdam, and Los Angeles. Cartons are labelled to FBA inbound spec and the declaration names Longgang as the origin. Partners who consolidate in Hong Kong usually take FOB Yantian and handle the last leg themselves.

How does AndroidSBC handle RMA or DOA replacements?

Answer: AndroidSBC targets a 0.3 percent DOA rate across the WF-Series, measured over the prior twelve months. On RMA, the partner returns the faulty WF-RK3588S unit to Longgang with its burn-in barcode, and a replacement ships within ten business days. Because the burn-in record is attached per unit, the failure analysis normally comes back with a root cause rather than a credit note.

Contact AndroidSBC: Start Your WF-RK3588S Sourcing Conversation

The AndroidSBC export desk handles all WF-Series enquiries from Jakarta and Indonesia. Direct factory contact on the WF-RK3588S and the rest of the som module and smarc carrier board line is available through:

• Email: Androidsbc@163.com
• Export service hotline: +8613261677119
• Website: https://www.androidsbc.com
• Destination market file: SDPPI type approval with SNI conformity for domestic sale for Indonesia, administered by SDPPI (Kominfo), entering at Port of Tanjung Priok on the Tanjung Priok to Shekou lane
• Source factory address: Wanlin Group, Building B, Building 1, Beisida Medical Device Building, 28 Nantong Avenue, Baolong Community, Baolong Sub-district, Longgang District, Shenzhen, Guangdong, China

OEM and ODM enquiries move fastest when the first message carries the annual volume, the certification scope, and the Incoterm. Send those three and the export desk replies with a per-lot quote and the full WF-Series MOQ matrix inside two business days.